No products in the cart.
BRICK AND BLOCK ACCESORIES
- Add to cart
- BRICK AND BLOCK ACCESORIES, VIEW ALL PRODUCTS
ADJUSTABLE VENEER ANCHORS FOR WOOD STUD
- Adjustable veneer anchors are used for anchoring brick veneer to wood stud with the #400 wood screw RJ-711 The plate is available in either 14 gauge or 12 gauge; the adjustable hook is made of 3/16" diameter wire. Availible in mill galvvanized, hbot dip galvanized and stainless steel. Hook lengths are 3-1/4", 4-1/4" and 5-1/4". Hook adjustments are a maximum…
- Add to cart
- Add to cart
- BRICK AND BLOCK ACCESORIES, VIEW ALL PRODUCTS
AQUAFLASH 500
- Aqua Flash 500 flashing is a composite sheet type waterproofing membrane consisting of 8 mils or high density cross laminated polyethylene bonded to 32 mils of rubberized asphalt for a total thickness of 40 mils.
- Add to cart
- Add to cart
- BRICK AND BLOCK ACCESORIES, VIEW ALL PRODUCTS
CAVITY NET
- Cavity Net I is a polymer core geomatrix composed of high-density polyethylene strands woven into an 80" thick mesh. The design allows moisture to seep down through any mortar droppings and exit the cavity wall through the weep holes. Used in cavity walls ranging from 1" to 1-3/4" in width. Cavity Net II is a 1.5" thick high-density polyethylene geometric…
- Add to cart
- Add to cart
- BRICK AND BLOCK ACCESORIES, VIEW ALL PRODUCTS
CELL VENT
- Cell Vent ( ultraviolet resistant polypropylene co-polymer) consists of many small, adjacent passageways bonded together in one unit. The cellular composition provides easy drainage for moisture along with the full height of the head joint.
- Add to cart
- Add to cart
- BRICK AND BLOCK ACCESORIES, VIEW ALL PRODUCTS
CORRUGATED WALL TIE
- 16 gauge or 22 gauge x 7/8" wide x 7" long. Finishes: mill galvanized, hot-dipped galvanized and stainless steel.
- Add to cart
- Add to cart
- BRICK AND BLOCK ACCESORIES, VIEW ALL PRODUCTS
EXPANSION JOINT W/ADHESIVE
- Compression up to 50%; manufactured of closed-cell neoprene conforming to ASTM D 1056, RE41 #3300 Non-adhasive. 3/8"x3"x50'. Packed 500feet per box.
- Add to cart
- Add to cart
- BRICK AND BLOCK ACCESORIES, VIEW ALL PRODUCTS
GROUT STOP
- Designed to prevent grout foam from falling through block core while maintaining a positive bond in the mortar joint. Constructructed of strong, non-corrosive 1/4" square polypropylene monofilament screen. Provides improved bonding of masonry anchor in hollow block construction. Available in 100'rolls.
- Add to cart
- Add to cart
- BRICK AND BLOCK ACCESORIES, VIEW ALL PRODUCTS
LADDER TYPE SERIES 200
- Ladder design is a prefabricated reinforcement for embedment in the horizontal mortar joints of the masonry. It is manufactured in 10'8" lengths from wire conforming to ASTM A 82/A82M for cold drawn steel wire. It consists of two or more parallel and deformed longitudinal wires welded to a perpendicular cross wire spaced 16" O.C. Out-to-out spacing in approximately two inches…
- Add to cart
- Add to cart
- BRICK AND BLOCK ACCESORIES, VIEW ALL PRODUCTS
MORTAR NET WEEP VENT
- WeepVent for masonry cavity walls helps ensure that moisture out and air can circulate into the cavity, and that insects can't enter the cavity through the week holes. The product's compressibility means it can fill the weep holes, and "prickly adhesion" holds the WeepVents in place without fasteners or adhesives. 90% open-weave polyester mesh. Available in Brown, Red, Tan, Almond,…
- Add to cart
- Add to cart
- BRICK AND BLOCK ACCESORIES, VIEW ALL PRODUCTS
PVC Control Joint
- Extruded from a specially formulated PVC compound with 85 durometer hardness conforming to ASTM D 2287 Type 654, ASTM D 240. It is designed for use in solid or cavity masonry wall construction at pilasters, columns, inter-sections or other joints. In long walls, control joints at 30-foot intervals are recommended to provide resilient resistance to cracking under stress of expansion…
- Add to cart
- Add to cart
- BRICK AND BLOCK ACCESORIES, VIEW ALL PRODUCTS
ROUND WEEP HOLES
- Clear round plastic weep holes are manufactured from Medium Density Polyethylene. Demensions: 3/8" O.D. x 1/4" I.D. x 4" #3600I - stainless steel filter & wick #3600H - cooper filter #3600G - stanless steel filter #3600W - wick #3600F - brass filter & wick #3600J - cooper filter & wick
- Add to cart
- Add to cart
- BRICK AND BLOCK ACCESORIES, VIEW ALL PRODUCTS
TRIANGLE 1100
- Triangular Ties constructed of steel wire meeting ASTM A1064/A1064M, A82/A82M. Available in 3/16" or 1/14" diameter. Finishes: mill galvanized, hot-dip galvanized and stainless steel. Standard size range from 3" to 9" in length.
- Add to cart
